Đầu đốt công nghiệp

HotLine (04)-2242 8148

Thiết bị đo điện đa năng

Tìm kiếm
Sản phẩm được quan tâm

Trang chủ > Thiết bị công nghiệp > Đầu đốt công nghiệp

Sắp xếp theo

- Incini-Cone Burners
- Mã SP: LAAEC-420
- Lượt xem: 5698
- Tình trạng:
- InciniCone Burners are designed for fume incineration and after-heating of exhaust from turbines, dryers, ovens and other similar equipment. The burner is mounted in the exhaust duct and requires the exhaust stream to supply all of the oxygen needed for complete combustion. Burner assemblies include the burner body, gas or oil gun, gas pilot with ignition plug and peepsight. Nine sizes are available.
- Giá NY: Liên hệ
- Giá bán: Liên hệ
- Khuyến mãi :
- ImmersoPak
- Mã SP: LAAEC-360
- Lượt xem: 5885
- Tình trạng:
- The Eclipse ImmersoPak (IP version 2) burner is ideal for heating immersion tubes on cleaning tanks, spray washers, salt baths, quenching tanks, tempering tanks, asphalt tanks and similar equipment. ImmersoPak is easy to install, simple to operate, and offers durability and long service life in industrial environments. It delivers smooth, quiet performance, even during cold starts.
- Giá NY: Liên hệ
- Giá bán: Liên hệ
- Khuyến mãi :
- ImmersoJet
- Mã SP: LAAEC-330
- Lượt xem: 5916
- Tình trạng:
- The ImmersoJet (IJ) is a nozzle-mix, tube-firing burner that is designed to fire at high velocities through a small diameter immersion tube in immersion heating tanks. The combustion gases from the burner scrub the inner tube surfaces to produce the highest heat transfer rate of any immersion burner available. It provides faster heat-up times than any other immersion burner. The standard burner includes a packaged blower, actuator control motor, integral butterfly valve, ratio regulator, burner body, combustion chamber, nozzle rear cover, spark and flame rods.
- Giá NY: Liên hệ
- Giá bán: Liên hệ
- Khuyến mãi :
- Single Ended Radiant Tube Burner
- Mã SP: LAAEC-325
- Lượt xem: 5342
- Tình trạng:
- The SER V5 burner delivers the best fuel efficiency of any burner in its class. With the burner and enhanced performance recuperator coaxially mounted inside a radiant tube, the SER V5 internally transfers combustion exhaust heat back to the burner air supply in a counterflow pattern, providing high preheat temperatures.
  
  The new, high efficiency recuperator design incorporates a unique dual finned combustor to provide an increased heat transfer surface for greater fuel savings. It also delivers exceptional heat flux and temperature uniformity.
- Giá NY: Liên hệ
- Giá bán: Liên hệ
- Khuyến mãi :
- E-Jector
- Mã SP: LAAEC-319
- Lượt xem: 6035
- Tình trạng:
- The Eclipse E-Jector is a flange mounted emission reduction device for use in radiant tubes. It accomodates diameters of 4" up to 6" with maximum capacities of up to 350,000 BTU/hr (102,5 kW). E-Jector provides significant reductions in NOx emissions. In field trials, NOx reductions were achieved of more than 50% over existing emission levels. The E-Jector is designed to be used with Eclipse Bayonet style Recuperators allowing for high fuel efficiencies while keeping NOx under control.
  
  Every burner system that includes an E-Jector is custom engineered by Eclipse to maximize performance and assure compatibility with the radiant tube.
- Giá NY: Liên hệ
- Giá bán: Liên hệ
- Khuyến mãi :
- Bayonet-Ultra Recuperator
- Mã SP: LAAEC-318
- Lượt xem: 5481
- Tình trạng:
- Exclusive multi-tube design delivers fuel savings up to 30%!
  
  Bayonet-Ultra recuperators are high efficiency heat exchangers designed to fit into the exhaust leg of single, U, O, W or Trident-type radiant tubes. They're frequently paired with Tube Firing burners and suitable for use with exhaust streams up to 2100 Degrees Fahrenheit provide fuel savings up to 30%.
  
  Conventional recuperators have only one heat transfer tube. Each Bayonet-Ultra contains multiple tubes to dramatically increase the heat transfer area while significantly decreasing the amount of fuel required to maintain required heat levels. Plus, an air cooled housing cools the work area.
- Giá NY: Liên hệ
- Giá bán: Liên hệ
- Khuyến mãi :
- Bayonet Recuperator
- Mã SP: LAAEC-317
- Lượt xem: 5666
- Tình trạng:
- Bayonet recuperators are low cost conventional heat exchangers designed to deliver preheated combustion air to the burner. They're frequently paired with tube firing burners to provide fuel savings up to 30%.
- Giá NY: Liên hệ
- Giá bán: Liên hệ
- Khuyến mãi :
- P-Tube
- Mã SP: LAAEC-315
- Lượt xem: 6036
- Tình trạng:
- The P-Tube burner is a radiant tube velocity burner for use in P-Tube furnace applications. The burner design utilizes flue gas recirculation entrained by the products of combustion. The flue gas recirculation provides lower NOx emissions and better tube temperature uniformity. By utilizing preheated combustion air, this burner delivers higher efficiencies than stand alone tube firing burners.
- Giá NY: Liên hệ
- Giá bán: Liên hệ
- Khuyến mãi :
- Tube Firing Burner
- Mã SP: LAAEC-310
- Lượt xem: 5790
- Tình trạng:
- Eclipse Tube Firing Burners are designed to fire radiant and immersion tubes with inputs from 25,000 to 2,000,000 Btu/hr. The unique nozzle design creates an intense adjustable-length flame with a vigorous spinning action. The long, spiraling flame results in cleaner combustion, efficient heat transfer and more precise, uniform tube temperatures. The flame scrubs the inside of the fire tubes to remove the gas film boundary layer and increase heat-transfer effectiveness with outstanding temperature uniformity. Not only do these factors contribute to longer tube life, they also ensure consistent uniform process heating.
- Giá NY: Liên hệ
- Giá bán: Liên hệ
- Khuyến mãi :
- Deep Spiral Flame Burner
- Mã SP: LAAEC-250
- Lượt xem: 5802
- Tình trạng:
- The Eclipse Spiral Flame and Dual-Fuel Flame Burners are a sealed nozzle mixing flat flame burner. Due to its unique construction, the flame follows the contour of the combustion block and surrounding furnace wall with virtually no forward velocity. This permits the burner to be placed close to the work load without producing flame impingement or hot spots in front of the burner and provides uniform heating over a large area.
  
  Eclipse Spiral Flame and Dual-Fuel Spiral Flame burners are used not only on new furnaces, but to increase work capacity on existing installations. Since work load can be placed proportionately closer to the burners, a greater portion of the furnace chamber can be used.
- Giá NY: Liên hệ
- Giá bán: Liên hệ
- Khuyến mãi :
- ExtensoHeat Burner
- Mã SP: LAAEC-235
- Lượt xem: 5790
- Tình trạng:
- The Eclipse ExtensoHeat Lance Burner offers the best solution available for continuous kiln heating furnaces for bricks, roof tiles and rough ceramic products. It is ideal for continuous kilns with roof top installations and furnace zones with operating temperatures above 1382ºF (750ºC). The burner lance extends through thick furnace walls to deliver the flame to the furnace load. ExtensoHeat is a nozzle mixing burner that can fire natural gas, propane, butane and other types of fuel gas.
- Giá NY: Liên hệ
- Giá bán: Liên hệ
- Khuyến mãi :
- ExtensoJet
- Mã SP: LAAEC-230
- Lượt xem: 5997
- Tình trạng:
- The ExtensoJet is a nozzle-mix burner that is designed to fire an intense stream of hot gases through a silicon tipped extended combustor using ambient combustion air. The ExtensoJet was designed to be extended through the kiln wall to significantly increase hot gas penetration and circulation of the products of combustion.
  The high velocity of the gases improves temperature uniformity, product quality and system efficiency. The gas velocity can be as high as 500/ft/s. The combustor comes in varying lengths from 20 inches to 56 inches.
- Giá NY: Liên hệ
- Giá bán: Liên hệ
- Khuyến mãi :
- ThermJet Liquid
- Mã SP: LAAEC-215
- Lượt xem: 5871
- Tình trạng:
- The ThermJet Liquid burners are nozzle mix burners for light or heavy oil. The burners are designed to operate on low pressure atomizing air and will operate efficiently throughout a wide operating range. The burner is based on the highly regarded ThermJet burner which is the industry standard for velocity burners. Typical applications include high temperature kilns and forge and melting furnaces.
  
  The ThermJet Liquid burners are available in three sizes with maximum capacities from 300,000 BTU/hr to 1,500,000 BTU/hr. All burner models can be controlled on-ratio with a cross-connected fuel regulator to maximize efficiency, or with fixed air to improve temperature uniformity in the furnace.
- Giá NY: Liên hệ
- Giá bán: Liên hệ
- Khuyến mãi :
- Furnnox
- Mã SP: LAAEC-210
- Lượt xem: 6709
- Tình trạng:
- Furnnox is an ultra low NOx direct fired furnace burner. The Furnnox is capable of producing NOx emissions less than 30 ppm at 3% O2 in most high temperature applications. To achieve high efficiency, the burner is controlled on-ratio throughout the operating range and can be operated with combustion air temperatures as high as 1,100°F (600°C).
  
  Furnnox burners set new standards for emissions and flexibility. Tests show that the Furnnox delivers lower emissions than any of its competitor's comparable burners. Furnnox is made to last, with rugged Eclipse dependability and reliability built in.
- Giá NY: Liên hệ
- Giá bán: Liên hệ
- Khuyến mãi :
- ThermJet Self-Recuperative Burner
- Mã SP: LAAEC-208
- Lượt xem: 5919
- Tình trạng:
- The Eclipse TJSR V5 is a direct fired, self-recuperative burner based on our industry proven ThermJet technology. This advanced burner design combines a high velocity flame with fuel saving recuperation. A space saving, integral eductor pulls the furnace exhaust through an internal ceramic recuperator. The recuperator preheats the incoming combustion air to very high levels, which improves furnace operating efficiency to reduce fuel usage by as much as 50% over typical ambient air burners.
  
  The TJSR V5 design eliminates the need for hot air ductwork required by external recuperators, providing savings in hardware and installation. The internally insulated heat exchanger section and exhaust housing hold heat in the recuperative section, adding to the heat recovery efficiency.
- Giá NY: Liên hệ
- Giá bán: Liên hệ
- Khuyến mãi :
- ThermJet Burners
- Mã SP: LAAEC-205
- Lượt xem: 6128
- Tình trạng:
- ThermJet is the industry standard for velocity burners, representing a technological leap forward in every area of design and performance that counts. ThermJet has the highest operating velocity of any burner available. Comparison tests with competitive models prove ThermJet delivers the lowest emissions. Integrated gas and air orifices simplify burner piping, set-up and adjustment. Air and gas inlets are independently adjustable in 90 degree increments to suit a variety of piping alternatives.Installation, operation, and maintenance are simplified and less costly.
  
  Made to last - rugged Eclipse dependability and reliability are built in. Available in fourteen sizes with maxmum capacities from 150,000 to 20,000,000 Btu/hr. All models are available for use with preheated combustion air.
- Giá NY: Liên hệ
- Giá bán: Liên hệ
- Khuyến mãi :
- InciniFume
- Mã SP: LAAEC-166
- Lượt xem: 7105
- Tình trạng:
- The InciniFume is an in-duct burner, originally developed by Eclipse for supplemental firing in power generation applications. The burner uses the oxygen within the exhaust flow to complete the combustion process. The short flame and uniform temperature distribution make it ideal for a variety of industrial processes requiring large heat inputs and high outlet temperatures. The design provides stable operation and clean combustion with a wide range of velocities, inputs and fuels. The InciniFume burner is modular in design and is assembled in straight sections, tee sections and crosses to produce nearly any configuration required.
- Giá NY: Liên hệ
- Giá bán: Liên hệ
- Khuyến mãi :
- FlueFire
- Mã SP: LAAEC-165
- Lượt xem: 6954
- Tình trạng:
- The Eclipse FlueFire has become an industry standard for supplemental firing in cogeneration and combined-cycle installations. FlueFire is an in-duct burner which can be located directly in the exhaust gases between the turbine and waste heat boiler. The burner is also suitable for fresh air operation or incineration applications.
  
  The FlueFire optimizes the system efficiency as it takes its oxygen requirement from the turbine exhaust gases. The burner can function with inlet temperatures up to 700°C (1300°F) and outlet temperatures up to 1200°C (2200°F). FlueFire is a proven performer in dozens of successful installations around the world.
- Giá NY: Liên hệ
- Giá bán: Liên hệ
- Khuyến mãi :
Trang:

1 2 3 4 5 6