bolting products minimax

• Size:
  Width (2.5in/63.5 mm)
  Height (6.5 in/165 mm)
  Depth (1.24 in/31.5 mm)
• Weight:
  13.5 ounces (with batteries).
• Keyboard:
  Membrane switch pad with
  twelve tactile keys.
• Operating Temperature:
  14 to 140F (-10C to 60C)
• Case:
  Extruded aluminum body with nickel-plated aluminum end caps (gasket sealed).
• Data Output:
  Bi-directional RS232 serial port. Windows® PC interface software.
• Display:
  1/8in VGA grayscale display (240 x 160 pixels). Viewable area 2.4 x 1.8in (62 x 45.7mm). EL backlit (on/off/auto).

ULTRASONIC SPECIFICATIONS MEASUREMENT

• Modes:
  Pulse-Echo (standard)
  Pulse-Echo w/Gate (fine adjust)
• Pulser:
  Square wave pulser with adjustable pulse width (spike, thin, wide).
• Receiver:
  Manual or Auto Set gain control with 40dB range.
• Timing:
  10 bit 250 MHz digitizer.
• Warranty:
  2 year limited

• Three 1.5V alkaline or
• 1.2V NiCad AA cells.
• Typically operates for 150 hours on alkaline and 100 hours on NiCad (charger not included.)
• Auto power off if idle 5 min.
• Battery status icon.

MEASURING

• Range: From 1″ to 48″ (25.4mm to 122cm) bolts.
• Time – Nanoseconds.
• Elongation – Change in length (inches/millimeters).
• Load – Force load applied (pounds kIP or kN Kilonewtons).
• Stress – Force for unit area stress applied (pounds kPSI or megapascals MPa).
• Strain % – percentage strain applied (inches per inch or millimeters per millimeter)
• Resolution:
  +/- .00001 inches (0.0001 mm)
• Velocity Range:
  .0492 to .3936 in/ms
  1250 to 9999 meters/sec
• Fixed, Single, and Two point zero calibration options.
• Select bolt material types from a preset or custom list.
• Units:
  English & Metric / Fahrenheit & Centigrade.

DISPLAY

• A-Scan – Rectified +/- (half wave view), or RF (full waveform view).
• Large Digits – Display and toggle between nanoseconds, elongation, load, stress, and strain.
  Digit Height: 0.400 in (10mm).
• Limits Bar(alarm limits) -
  Set Hi & Lo alarm limits for displaying an acceptable tolerance range.
• Repeatability Bar Graph – Bar graph indicates stability of measurement.

• Total of 8,000 readings, multiple bolt groups. Stores both waveform views, nanoseconds, elongation, load, stress, and strain for each reading.

MEMORY

• 16 megabit non-volatile ram.
  Transducer

TRANSDUCER TYPES:

• Single Element (1 to 10 MHz & 1/8″ to 1″diameters).
• Locking quick disconnect
  “00″ LEMO connectors.
• Standard 10 foot cable.
• Custom transducers and cable lengths available on request.
• Temperature probe for automatic temperature compensation.

FEATURES:

• Setups:
  64 custom user defined setups. Factory setups can also be edited by the user.
• Gate:
  Gate used to fine adjust where the detection point occurs.
• Alarm Limits:
  Set hi and lo tolerances with audible beeper, viewable scan bar, and visual LEDs.
• Auto Set:
  Locates the detection signal, optimizes the gain setting, and adjusts the overall display to show the waveform and detection point automatically.
• Field Calibration:
  Vector & linear regression.
  Certification
  Factory calibration traceable to national standards.